Alpha-technologies Cordex Controller Ver.3.1x Manual de usuario descargar pdf (Pagina 82)

0700015-J0 Rev B

ADIO Conﬁgure Signals – enables the Supervisor to input a value for a range to apply to all selected

channels. In this case, the BCMC if so equipped:

Figure 87 — BCMC configuration example one (set DCCT range in Amps)

ADIO Static Calibration (Web Interface Only) – enables the Supervisor to calibrate ADIO (except BCMC)

analog inputs without the need for a live signal at the input. This is similar to Static Calibration for control-

ler analog inputs described previously.

Figure 88 — BCMC configuration example two (set String Current range in Amps)

1 2 ... 77 78 79 80 81 82 83 84 85 86 87 ... 143 144

Your Power Solutions Partner 1
User Manual 1
Version 3.1x 3
Contents 4
List of Tables 7
1. Introduction 8
2. Standard Features 9
2.4 Mixed Rectiﬁer System 10
2.5 Safe Voltage 10
2.6 Power Save 10
2.7 Auto DC Priority 10
2.11 Battery Test Scheduler 12
2.13 Signals Management 12
2.14.1 Analog Statistics 13
2.14. 2 Battery Log 13
2.14.3 Data Logging 14
2.14.4 Event Log 14
3. User Interface Options 15
3.4 Menu Navigation - LCD 17
3.4.3 Logging Out 18
3.4.4 Virtual Numeric Keypad 18
3.4.5 LCD Menu Structure 18
Count down 20
4.2 Language Selection 21
4.1 Start-up 21
4.3 Date and Time 22
4.5.1 Silence All Alarms 23
4.6 Signals Display 24
4.7.1 Inventory Update 26
To change modes: 27
4.9 Float (FL) Mode 28
4.10 Equalize (EQ) Mode 28
4.11 Boost (BST) Mode 28
4.12.3 BT Initiation 29
4.13 Communications 30
5.1 Communication Settings 31
5.2 Getting Started 32
5.3 Login 33
5.4 Language Selection 33
5.5 Saving Changes 33
5.6 Date & Time 34
5.8 Converters 35
5.9 Rectiﬁers 35
5.10 Inverters 35
Figure 30 — CXCU controller 36
Controller > 36
6.1 System Info 38
6.1.3 Set ADIO Module Number 39
6.1.4 Site Information 39
6.1.5 Temperature Units 40
6.1.6 Factory Information 40
6.2 Converters 41
6.3 Rectiﬁers 41
6.4 Inverters 45
6.4.4 General Settings 48
6.4.5 Set Inputs 49
6.4.7 Auto DC Priority 50
6.5 Batteries 52
6.5.3 Battery Monitor 53
6.5.5 Boost (BST) Mode 55
6.5.7 Battery Properties 56
6.5.8 Battery Information 57
6.5.9 Battery Test Scheduler 57
Enable Periodic BT 58
Enable Scheduled BT 58
6.6 Alarms 59
6.6.3 Conﬁguring Alarms 60
6.6.4.1 Rectiﬁer Alarms 62
6.6.4.2 Digital Alarms 63
6.6.5.5 Miscellaneous Alarms 65
6.6.5.6 ADIO Alarms 66
6.6.5.7 Custom Alarms (1-20) 66
6.6.5.8 Converter Alarms 68
6.6.8 Alarm Tone 71
6.6.9 Conﬁguring ALCO 71
6.7 Signals 72
6.7. 2.1 Controller Signals 74
6.7. 2 Conﬁgure Signals 74
6.7.2.2 Analog Inputs 75
6.7. 2. 3 Digital Inputs 75
6.7. 2.4 Rectiﬁer Signals 75
6.7. 2. 5 Custom Signals 75
(in Amperes/50 mV) 76
6.7.2.7 Midnight Rollover 77
6.7. 2. 8 Converter Signals 78
6.7. 2.9 Inverters 78
6.7. 2.10 Timers 79
6.7. 2.11 Counters 79
6.7. 2.12 ADIO Signals 80
Figure 92 — Log Frequency 84
6.7.3.3 Retrieve Logs 85
6.8 Controls 91
6.9 Communications 93
6.10 Hardware 95
6.11.1 Retrieve Logs 96
6.12 Supervisor 98
7. Advanced Programming 100
7.3 Tips on Programming 101
8.2 PPP Connection Devices 103
8.3 Rear Port Conﬁguration 104
CAUTION! 105
9. Remote Communications 106
9.2.3.1 Modem Conﬁguration 109
0700015-J0 Rev B 110
COM port as shown below: 110
Figure 139 — Modem Status 112
9.3 Modem Connection 113
9.3.2 Computer Setup 114
10.1 Overview 115
10.1.3 Typical UDP Transport 116
Figure 142 — VarBinds 117
10.3.2 SNMP Trap Recovery 118
Submenu Item 127
Default Setting Units 129
Alarm Type Cause Solution 132
PDU Address 139
Number of 139
13. Trouble-shooting 141
14. Alpha Conventions 142
Visit us at www.alpha.ca 144

Comentarios a estos manuales

Sin comentarios

Alpha-technologies Cordex Controller Ver.3.1x Manual de usuario Pagina 82

Comentarios a estos manuales

Relacionado con productos y manuales para Software Alpha-technologies Cordex Controller Ver.3.1x